Aqua Hair Sticks/Shawl Pins

What you need

Wooden end-drilled hair sticks
Aqua lampwork beads
Silver bead caps to fit the lampwork beads
Crystal and aqua Czech firepolish beads
Silver daisy spacers
Silver headpins
Epoxy resin adhesive



Instructions

Take the hair sticks or shawl pins and poke them into a block of styrofoam to keep them upright. 

Mix the epoxy resin components and drizzle some adhesive into the holes in the hair sticks.  Cut the end off a headpin and place the cut end into the hole and adhesive.  Place a little adhesive around the end of the hair stick.  Thread the lampwork bead onto the head pin and make sure that it contacts the adhesive without leaving any squeeze out.  Leave to dry for at least an hour.

Thread your bead cap and a small crystal-coloured bead onto the headpin the lampwork bead is attached to.  Cut the headpin, leaving about 7mm to create a loop to attach the dangle to.

To creat the dangle, thread firepolish beads and silver daisy spacers to your preferred design.  Then cut the headpin to length, create a loop and attach to the first loop you created.

Repeat to create a second hair stick or shawl pin.

Liked this project? Subscribe to our weekly newsletter and get more like this!




Aqua Hair Sticks/Shawl Pins

What you need

Wooden end-drilled hair sticks
Aqua lampwork beads
Silver bead caps to fit the lampwork beads
Crystal and aqua Czech firepolish beads
Silver daisy spacers
Silver headpins
Epoxy resin adhesive



Instructions

Take the hair sticks or shawl pins and poke them into a block of styrofoam to keep them upright. 

Mix the epoxy resin components and drizzle some adhesive into the holes in the hair sticks.  Cut the end off a headpin and place the cut end into the hole and adhesive.  Place a little adhesive around the end of the hair stick.  Thread the lampwork bead onto the head pin and make sure that it contacts the adhesive without leaving any squeeze out.  Leave to dry for at least an hour.

Thread your bead cap and a small crystal-coloured bead onto the headpin the lampwork bead is attached to.  Cut the headpin, leaving about 7mm to create a loop to attach the dangle to.

To creat the dangle, thread firepolish beads and silver daisy spacers to your preferred design.  Then cut the headpin to length, create a loop and attach to the first loop you created.

Repeat to create a second hair stick or shawl pin.

Liked this project? Subscribe to our weekly newsletter and get more like this!


Aqua Hair Sticks/Shawl Pins



Aqua Hair Sticks/Shawl Pins

What you need

Wooden end-drilled hair sticks
Aqua lampwork beads
Silver bead caps to fit the lampwork beads
Crystal and aqua Czech firepolish beads
Silver daisy spacers
Silver headpins
Epoxy resin adhesive



Instructions

Take the hair sticks or shawl pins and poke them into a block of styrofoam to keep them upright. 

Mix the epoxy resin components and drizzle some adhesive into the holes in the hair sticks.  Cut the end off a headpin and place the cut end into the hole and adhesive.  Place a little adhesive around the end of the hair stick.  Thread the lampwork bead onto the head pin and make sure that it contacts the adhesive without leaving any squeeze out.  Leave to dry for at least an hour.

Thread your bead cap and a small crystal-coloured bead onto the headpin the lampwork bead is attached to.  Cut the headpin, leaving about 7mm to create a loop to attach the dangle to.

To creat the dangle, thread firepolish beads and silver daisy spacers to your preferred design.  Then cut the headpin to length, create a loop and attach to the first loop you created.

Repeat to create a second hair stick or shawl pin.

Liked this project? Subscribe to our weekly newsletter and get more like this!



Comments

  1. These are beautiful..its hard for me to find nice pieces for my hair…im so picky.

  2. Beautiful! Thanks for the instruction!

    xoxox, Daff

What do you think of this project? Let us know!